TLC59116IPWR LED Lighting Drivers 16Ch Fm I2C Bus Cons Crnt LED Sink Drvr

Short Description:

Manufacturers: Texas Instruments
Product Category: LED Lighting Drivers
Data Sheet:TLC59116IPWR
RoHS status: RoHS Compliant

Product Detail



Product Tags

♠ Product Description

Product Attribute Attribute Value
Manufacturer: Texas Instruments
Product Category: LED Lighting Drivers
RoHS:  Details
Series: TLC59116
Mounting Style: SMD/SMT
Package/Case: TSSOP-28
Number of Outputs: 16 Output
Output Current: 120 mA
Input Voltage, Min: 3 V
Input Voltage, Max: 5.5 V
Topology: Boost
Operating Frequency: 1 MHz
Output Voltage: 17 V
Minimum Operating Temperature: - 40 C
Maximum Operating Temperature: + 85 C
Packaging: Reel
Packaging: Cut Tape
Packaging: MouseReel
Features: I2C Control, Constant Current
Brand: Texas Instruments
Input Voltage: 3 V to 5.5 V
Low Level Output Current: 30 mA
Number of Channels: 16 Channel
Operating Supply Voltage: 3 V to 5.5 V
Operating Temperature Range: - 40 C to + 85 C
Output Type: Constant Current
Pd - Power Dissipation: 1207 mW
Product Type: LED Lighting Drivers
Factory Pack Quantity: 2000
Subcategory: Driver ICs
Supply Current - Max: 37 mA
Type: Linear
Unit Weight: 117.500 mg

♠ TLC59116 16-Channel FM+ I 2C-Bus Constant-Current LED Sink Driver

The TLC59116 is an I 2C bus controlled 16-channel LED driver that is optimized for red/green/blue/amber (RGBA) color mixing and backlight application. Each LED output has its own 8-bit resolution (256 steps) fixed-frequency individual PWM controller that operates at 97 kHz, with a duty cycle that is adjustable from 0% to 99.6%.

  • Previous:
  • Next:

  • • 16 LED Drivers (Each Output Programmable at Off, On, Programmable LED Brightness, or Programmable Group Dimming and Blinking Programmable Group Dimming and Blinking Mixed With Individual LED Brightness)

    • 16 Constant-Current Output Channels 

    • 256-Step (8-Bit) Linear Programmable Brightness Per LED Output Varying From Fully Off (Default) to Maximum Brightness Using a 97-kHz PWM Signal

    • 256-Step Group Brightness Control Allows General Dimming [Using a 190-Hz PWM Signal  From Fully Off to Maximum Brightness (Default)

    • 256-Step Group Blinking With Frequency Programmable From 24 Hz to 10.73 s and Duty  Cycle From 0% to 99.6%

    • Four Hardware Address Pins Allow 14 TLC59116  Devices to Be Connected to Same I 2C bus

    • Four Software-Programmable I 2C Bus Addresses (One LED Group Call Address and Three LED Sub Call Addresses) Allow Groups of Devices to Be Addressed at Same Time in Any Combination

    • Software Reset Feature (SWRST Call) Allows Device to Be Reset Through I 2C Bus

    • Up to 14 Possible Hardware-Adjustable Individual I 2C Bus Addresses Per Device, So That Each Device Can Be Programmed

    • Open-Load and Overtemperature Detection Mode to Detect Individual LED Errors

    • Output State Change Programmable on Acknowledge or Stop Command to Update Outputs Byte-by-Byte or All at Same Time (Default to Change on Stop)

    • Output Current Adjusted Through an External Resistor

    • Constant Output Current Range: 5 mA to 120 mA

    • Maximum Output Voltage: 17 V

    • 25-MHz Internal Oscillator Requires No External Components

    • 1-MHz Fast-mode Plus (FMT) Compatible I 2C Bus Interface With 30-mA High-Drive Capability on SDA Output for Driving High-Capacitive Buses

    • Internal Power-On Reset

    • Noise Filter on SCL and SDA Inputs

    • No Glitch on Power-Up

    • Active-Low Reset

    • Supports Hot Insertion

    • Low Standby Current

    • 3.3-V or 5-V Supply Voltage

    • 5.5-V Tolerant Inputs

    • Offered in 28-Pin Thin Shrink Small-Outline Package (TSSOP) (PW) and 32-Pin Quad Flatpack No Lead (QFN)

    • –40 °C to 85 °C Operation

    • Gaming

    • Small Signage

    • Industrial Equipment

    Related Products